PermaDecal (indoor/outdoor) Fox Red Labrador Retriever

PermaDecal – Premium Decal Transfer

Meet your new favorite forever decal.

PermaDecal transfers are printed using high-quality DTF (Direct-to-Film) technology on durable transparent film for a clean, seamless look on smooth surfaces. Unlike traditional paper stickers or basic vinyl decals, these are made to last — waterproof, scratch-resistant, and UV protected for long-term indoor or outdoor use.

They apply easily and bond securely, making them perfect for glass, metal, sealed plastic, tumblers, windows, laptops, coolers, and more.

If you want a bold design without peeling edges or fading graphics, this is it.

Product Features

• Durable transparent film with strong permanent adhesive

• UV-protected matte laminate for fade resistance

• Waterproof & scratch-resistant finish

• Crisp, vibrant print detail

• Designed for smooth, hard surfaces

Application Instructions

1. Clean surface thoroughly with alcohol or mild cleaner.

2. Ensure surface is completely dry.

3. Apply carefully to a smooth surface and press firmly.

Best results occur on glass, metal, sealed wood, ceramic, and hard plastics.

Important Disclaimer

PermaDecal transfers adhere very strongly. While many can be removed using heat and adhesive solvent, removal results depend on surface type, paint condition, and environmental exposure.

 

Buyer assumes responsibility for proper surface selection and application. Seller is not responsible for damage resulting from improper application, removal, or misuse.

Step 1: Prepare the Surface & PermaDecal Clean the Surface For the best long-term adhesion, apply your PermaDecal to a clean, dry surface. If needed, wipe the area with: Mild soap and water, or A 50/50 mixture of rubbing alcohol and water. Allow the surface to dry completely before application. While cleaning isn't always required, it helps your PermaDecal withstand weather, washing, and everyday wear. Pre-Burnish the Design Before removing the backing, place your PermaDecal face down so the back of the decal is facing up. Using the felt or padded edge of your squeegee, apply firm, even pressure across the entire design 2–4 times. Pay extra attention to small lettering, thin lines, and delicate details to ensure they fully adhere to the transfer film. ________________________________________ Step 2: Remove the Backing Slowly separate the clear transfer film from the back of the decal As you peel, carefully watch that every part of the design lifts onto the clear transfer film. Take your time—especially with intricate designs or small text. If any portion remains on the backing paper: Lay it back down. Burnish that area again with the squeegee. Try peeling from a slightly different angle. Slow and steady gives the best results. ________________________________________ Step 3: Position Your PermaDecal Decide exactly where you'd like your PermaDecal before pressing it into place. Small Designs (4" and under) Position the decal carefully using both hands, then press it onto the surface. Larger Designs (6" and larger) For larger decals, it's often easiest to start applying from one edge and slowly work across to the opposite side. This helps prevent air bubbles, wrinkles, and accidental shifting of the design. Helpful Tip: Leave one corner of the transfer film loose until you're ready to remove it. This makes peeling much easier after application. ________________________________________ Step 4: Complete the Transfer Once your PermaDecal is in position, firmly burnish the entire design with the squeegee 2–4 times, using even pressure. Instead of peeling outward, be sure to roll the transfer film downward slowly while watching to make sure every part of the design remains attached to your surface. If any section begins lifting with the transfer film: Lay the film back down. Burnish that area again with firm pressure. Slowly continue peeling. Take your time—the slower you peel, the better your results. ________________________________________ Caring for Your PermaDecal Apply only to clean, smooth, non-porous surfaces. Allow the adhesive to cure for 24 hours before washing or exposing it to heavy moisture. Hand washing is recommended whenever possible. Avoid abrasive scrubbers or harsh chemicals directly on the decal. Once applied, PermaDecals are designed to be permanent and cannot be repositioned without damaging the design.